• "

Ordering

目录nhO嘉泰姆

1.产品概述                       2.产品特点nhO嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 nhO嘉泰姆
5.产品封装图                     6.电路原理图                   nhO嘉泰姆
7.功能概述                        8.相关产品nhO嘉泰姆

一,产品概述(General Description)   nhO嘉泰姆

 CXSD62130 CXSD62130A is a 1.5MHz high efficiency monolithic synchronous buck regulator. Design with current mode scheme,the CXSD62130 CXSD62130A is stable nhO嘉泰姆

with ceramic output capacitor. Input voltage from 2.7V to 6.0V makes the nhO嘉泰姆

CXSD62130 CXSD62130A ideally suited for single Li-Ion battery powered nhO嘉泰姆

applications. 100%duty cycle provides low dropout operation, extending nhO嘉泰姆

battery life in portable electrical devices. Theinternally fixed 1.5MHz nhO嘉泰姆

operating frequency allows the using of small surface mount inductors and capacitors. The synchronous switches included inside increase the efficiencynhO嘉泰姆

and eliminate the need of an external Schottky diode.nhO嘉泰姆
   The CXSD62130 CXSD62130A is available in TDFN2x2-6 packages.nhO嘉泰姆
二.产品特点(Features)nhO嘉泰姆

1A Output CurrentnhO嘉泰姆
Wide 2.7V~6.0V Input VoltagenhO嘉泰姆
Fixed 1.5MHz Switching FrequencynhO嘉泰姆
Low Dropout Operating at 100% Duty CyclenhO嘉泰姆
25μA Quiescent CurrentnhO嘉泰姆
Synchronous RectifiernhO嘉泰姆
0.6V Reference VoltagenhO嘉泰姆
<0.5μA Input Current During ShutdownnhO嘉泰姆
Short-Circuit ProtectionnhO嘉泰姆
Over-Temperature ProtectionnhO嘉泰姆
Available in TDFN2x2-6 PackagesnhO嘉泰姆
Lead Free and Green Devices AvailablenhO嘉泰姆
(RoHS Compliant)nhO嘉泰姆
三,应用范围 (Applications)nhO嘉泰姆

HD STBnhO嘉泰姆
BT MousenhO嘉泰姆
PND InstrumentnhO嘉泰姆
Portable InstrumentnhO嘉泰姆
四.下载产品资料PDF文档 nhO嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！nhO嘉泰姆

 nhO嘉泰姆

五,产品封装图 (Package)nhO嘉泰姆

nhO嘉泰姆
六.电路原理图nhO嘉泰姆

nhO嘉泰姆
nhO嘉泰姆

七,功能概述nhO嘉泰姆

Main Control LoopnhO嘉泰姆
The CXSD62130 CXSD62130A is a constant frequency, synchronous rectifier and current-mode nhO嘉泰姆

switching regulato r. In normal operation, the internal P-channel power MOSFET is turned on eachnhO嘉泰姆

 cycle. The peak inductor current at which ICMP turn off the P-FET is controlled by the voltage onnhO嘉泰姆

 the COMP node, which is the output of the error amplifier (EAMP). An external resistive divider nhO嘉泰姆

connected between VOUT and ground allows the EAMP to receive an output feedback voltage nhO嘉泰姆

VFB at FB pin. When the load current increases, it causes a slightly decrease in VFB relative tonhO嘉泰姆

the 0.6V reference, which in turn causes the COMP voltage to increase until the average nhO嘉泰姆

inductor current matches the new load current.nhO嘉泰姆
Enable/ShutdownnhO嘉泰姆
Driving RUN to the ground places the CXSD62130 CXSD62130A in shutdown mode. WhennhO嘉泰姆

 in shutdown, the internal power MOSFETs turn off, all internal circuitry shuts down and thenhO嘉泰姆

 quiescent supply current reduces to 0.5μA maximum.nhO嘉泰姆
Pulse Frequency Modulation Mode (PFM)nhO嘉泰姆
The CXSD62130 CXSD62130A is a fixed frequency, peak current mode PWM step-down nhO嘉泰姆

converter. At light loads, the CXSD62130 CXSD62130A will automatically enter in pulse nhO嘉泰姆

frequency mode operation to reduce the dominant switching losses. In PFM operation, nhO嘉泰姆

the inductor current may reach zero or reverse on each pulse. A zero current comparator nhO嘉泰姆

turn off the N-FET, forcing DCM operation at light load. These controls get very low nhO嘉泰姆

quiescent current, help to maintain high effi-ciency over the complete load range.nhO嘉泰姆
Slope Compensation and Inductor Peak CurrentnhO嘉泰姆
The CXSD62130 CXSD62130A is a peak current mode PWM step downconverter. TonhO嘉泰姆

 prevent sub-harmonic oscillations, theCXSD62130 CXSD62130A sense the peak current and nhO嘉泰姆

add slope compensation to stable the converter. It is accomplished in-ternally by addingnhO嘉泰姆

a compensating ramp to the inductor current signal at duty cycles in excess of 40%.nhO嘉泰姆

 Normally,this results in a reduction of maximum inductor peak current for duty cycles >nhO嘉泰姆

 40%. However, the CXSD62130 CXSD62130A uses a special scheme that counteracts this nhO嘉泰姆

compensating ramp, which allows the maximum inductor peak current to remain unaffectednhO嘉泰姆

 throughout all duty cycles.nhO嘉泰姆
Dropout OperationnhO嘉泰姆
As the input supply voltage decreases to a value ap-proaching the output voltage, the dutynhO嘉泰姆

 cycle increases toward the maximum on time. Further, reduction of thesupply voltage forces nhO嘉泰姆

the main switch to remain on for more than one cycle until it reaches 100% duty cycle. ThenhO嘉泰姆

 input voltage minus the voltage drop will determine the output voltage across the P-FETnhO嘉泰姆

 and the inductor.An important detail to remember is that on resistance of P-FET switch nhO嘉泰姆

will increase at low input supply voltageTherefore, the user should calculate the power dissipa-nhO嘉泰姆
tion when the CXSD62130 CXSD62130A is used at 100% duty cycle with low input voltage.nhO嘉泰姆
Over-Temperature Protection (OTP)nhO嘉泰姆
The over-temperature circuit limits the junction tempera-ture of the CXSD62130 CXSD62130A. nhO嘉泰姆

When the junction temperature ex-ceeds 150oC, a thermal sensor turns off the both power nhO嘉泰姆

MOSFETs, allowing the devices to cool. The thermal sen-sor allows the converters to start a nhO嘉泰姆

soft-start process and regulate the output voltage again after the junction tem-perature coolsnhO嘉泰姆

 by 30oC. The OTP is designed with a 30oC hysteresis to lower the average JunctionnhO嘉泰姆

 Temperature (TJ) during continuous thermal overload conditions, in-creasing the lifetime nhO嘉泰姆

of the device.nhO嘉泰姆
八,相关产品                    更多同类产品.......nhO嘉泰姆

◀ Previous:CXSD62129A consists of two independent 1.5MHz con- stant frequency current mode and PWM step-down converters. Each converter integrates a main switch with a synchronous rectifier

Back to top

Next▶:1.5MHz high efficiency monolithic synchronous buck regulator. Design with current mode scheme,CXSD62130 CXSD62130A stable with ceramic output capacitor.