• [ CXLE8856 ]"

Ordering

目录38W嘉泰姆

1.产品概述                       2.产品特点38W嘉泰姆
3.应用范围                       4.下载产品资料PDF文档 38W嘉泰姆
5.产品封装图                     6.电路原理图                   38W嘉泰姆
7.功能概述                        8.相关产品38W嘉泰姆

一,产品概述(General Description)    38W嘉泰姆

   The CXLE8856 is a set-up DC-DC converter that delivers a regulated output current. The device switches at a 1.0MHz constant frequency, allowing for the38W嘉泰姆
use of small value external inductor and ceramic capacitors.The CXLE8856 is targeted to be used for driving loads up to 1A from a two-cell alkaline battery.38W嘉泰姆
    The LED current can be auto adjusted by internal smart module and programmed by the external current sense resistor, Rs,connected between the feedback pin (FB) and ground. A low 95mV(TYP.) feedback voltage reduces the power38W嘉泰姆
loss in the Rs for better efficiency. With its internal 2A,100mΩ NMOS switch, the device can provide high efficiency even at heavy load. During the shutdown38W嘉泰姆
mode, the feedback resistor Rs and the load are completely disconnected and the current consumption is reduced to 1uA.The CXLE8856 is available in the 6-lead38W嘉泰姆
SOT-23-6L package.38W嘉泰姆
二.产品特点(Features)38W嘉泰姆

LED Power Efficiency: up to 90%38W嘉泰姆
Current Accuracy: 5%(Vin =3.6V to 1.8V38W嘉泰姆
@Vf =3.7V)38W嘉泰姆
Low Start-Up Voltage: 0.9V38W嘉泰姆
Low Hold Voltage:0.75V38W嘉泰姆
1MHz Switching Frequency38W嘉泰姆
Uses small, Low Profile External Components38W嘉泰姆
Low RDS(ON) : 100mΩ (TYP.)38W嘉泰姆
Over Temperature Protection38W嘉泰姆
Low Profile SOT-23-6L Package38W嘉泰姆
三,应用范围 (Applications)38W嘉泰姆

White LED Torch (Flashlight)38W嘉泰姆
White LED Camera Flash38W嘉泰姆
DSC(Digital Still Camera)Flash38W嘉泰姆
Cellular Camera Phone Flash38W嘉泰姆
PDA Camera Flash38W嘉泰姆
Camcorder Torch(Flashlight) Lamp38W嘉泰姆
四.下载产品资料PDF文档 38W嘉泰姆

需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！38W嘉泰姆

 38W嘉泰姆

五,产品封装图 (Package)38W嘉泰姆

38W嘉泰姆

六.电路原理图38W嘉泰姆

38W嘉泰姆
七,功能概述38W嘉泰姆

Inductor Selection38W嘉泰姆
The CXLE8856 can use small value inductors due to its switching frequency of 1MHz. The value of inductor will focus in the range of 2.2uH to 4.7uH for most CXLE8856 applications. In typical high current white LED applications,it is recommended to use a 4.7uH inductor. The inductor should have low DCR (DC resistance) to minimize the IR power loss, and it requires a current rating of 2A to handle the peak inductor current without saturating. 38W嘉泰姆
Capacitor Selection38W嘉泰姆
An input capacitor is required to reduce the input ripple and noise for proper operation of the CXLE8856. For good input decoupling,  Low  ESR(equivalent  series  resistance) capacitors should be used at the input. At least 2.2uF input capacitor  is  recommended  for  most  applications. A minimum output capacitor value of 6.8uF is recommended under normal operating conditions, while a 10uF-22uF capacitor may be required for higher power LED current. A reasonable value of the output capacitor depends on the LED current. The ESR of the output capacitor is the important parameter to determine the output voltage ripple of the converter, so low ESR capacitors should be used at the output to reduce the output voltage ripple. The small size of ceramic capacitors is an excellent choice for CXLE8856 applications. The X5R and X7R types are preferred because they maintain capacitance over wide voltage and temperature ranges.38W嘉泰姆
Diode Selection38W嘉泰姆
It's indispensable to use a Schottky diode rated at 2A with the CXLE8856. Using a Schottky diode with a lower forward voltage drop is better to improve the power LED efficiency, and its voltage rating should be greater than the output voltage. In application, the ON Semiconductor MBRA210LT3G is recommended. 38W嘉泰姆
LED Current Setting38W嘉泰姆
The LED current is set by the single external Rs resistor connected to the FB pin as shown in the typical application circuit on page 1. The typical FB reference is internally regulated to 95mV(TYP.). The LED current is 95mV/Rs. It's recommended to use a 1% or better precision resistor for the better LED current accuracy.38W嘉泰姆
The formula and table 1 for Rs selection are shown as follows:38W嘉泰姆
Rs=95mV/ILED38W嘉泰姆
PCB Layout Guidelines38W嘉泰姆
For best performance of the CXLE8856, the following guidelines must be strictly followed. Input and Output capacitors should be placed close to the IC and connected to ground plane to reduce noise coupling.Keep the main current traces as possible as short and wide.SW node of DC-DC converter is with high frequency voltage swing. It should be kept at a small area.Place the feedback components as close as possible to the IC and keep away from the noisy devices.38W嘉泰姆
八,相关产品                  更多同类产品.......38W嘉泰姆

◀ Previous:Cxle8709a is a LED Driver IC manufactured by CMOS technology which has the characteristics of simple peripheral circuit low starting voltage 0.9V (typical value) low ripple low noise

Back to top

Next▶:Cxle8857b is a boost DC/DC converter with wide input voltage range (0.8~5.5V) adjustable constant current and limited current to drive white LED