The CXEP2330 is a high-accuracy analog front-end (AFE) IC that provides measurements for four-quadrant 3-phase metering. The combination of a 21-bit sigma-delta analog-to-digital converter with a six-input AFE, a thermally compensated high-precision reference, and a compute engine results in high accuracy and wide dynamic range. Our Single Converter Technology reduces crosstalk and cost. This IC also provides a real-time clock (RTC) and battery backup for time-of-use (TOU) metering.The host processor communicates with the CXEP2330 through a UART interface using the programmable IRQZ interrupt. The CXEP2330 calculates and accumulates meter measurements for each accumulation interval. A high-speed synchronous serial port (SSI) is provided to facilitate high-end metering. Integrated rectifying functions on the battery-backup circuit enable minimal external component usage and minimum backup current. Also, eight multipurpose pins are provided for control of peripherals
-
[ CXEP2330 ]"
目录
7.相关产品
产品概述 返回TOP
The CXEP2330 is a high-accuracy analog front-end (AFE) IC that provides measurements for four-quadrant 3-phase metering. The combination of a 21-bit sigma-delta analog-to-digital converter with a six-input AFE, a thermally compensated high-precision reference, and a compute engine results in high accuracy and wide dynamic range. Our Single Converter Technology reduces crosstalk and cost. This IC also provides a real-time clock (RTC) and battery backup for time-of-use (TOU) metering.The host processor communicates with the CXEP2330 through a UART interface using the programmable IRQZ interrupt. The CXEP2330 calculates and accumulates meter measurements for each accumulation interval. A high-speed synchronous serial port (SSI) is provided to facilitate high-end metering. Integrated rectifying functions on the battery-backup circuit enable minimal external component usage and minimum backup current. Also, eight multipurpose pins are provided for control of peripherals.
产品特点 返回TOP
High Accuracy
< 0.1% Wh accuracy over 2000:1 range
Exceeds IEC 62053/ANSIC 12.20 specifications
Up to 10ppm/
C precision ultra-stable voltage reference
Single Converter Technology reduces cross talk and power consumption
Six sensor inputs—referenced to V3P3
Compatible with CTs, resistive shunts and Rogowski Coil sensors
Digital temperature compensation
Sag detection
Measures Wh, VARh, VAh, Vrms, Irms, V-to-V phase and load angle on each phase
Four-quadrant metering.
Four low-jitter pulse outputs from selectable measurements
Four pulse count registers
Selectable default status for pulse pins
Same calibration data for 46Hz to 64Hz line frequency
Broad CT phase compensation (±7deg) Battery Backup
Powers real-time clock during power supply outage
Compatible with Li-ion, NiCd, or super capacitor
Battery backup current 2μA typical at 25°C
External Data Interface
UART control interface, two selectable data rates
8 general-purpose I/O pins with alarm capability
5 or 10MHz selectable high-speed synchronous serial output for DSP interface
IRQ output signal for alarms and end of measurement intervals
Alarms on voltage sag, overvoltage, overcurrent Low System Cost
Power consumption 30mW at 3.3V typical
Real-time clock with temperature compensation
Built-in power-fault detection
Single 32kHz crystal time base
Single-supply operation (3.3V)
64-lead LQFP package
应用范围 返回TOP
Industrial, Commercial, and Residential Meters
技术规格书（产品PDF) 返回TOP
需要详细的PDF规格书请扫一扫微信联系我们，还可以获得免费样品以及技术支持！
产品封装图 返回TOP
电路原理图 返回TOP
相关芯片选择指南 返回TOP 更多同类产品......
|
Electricity Metering ICs |
||||||||||
|
Part Number |
Phase |
Internal Flash(KB) |
Internal RAM(KB) |
Analog Input |
Sensor Inputs (Current+Voltage) |
MCU MIPS |
RTC |
LCD Driver Pixels(max) |
GPIO |
UARTs |
|
3P |
||||||||||
|
3P |
||||||||||
|
1P |
||||||||||
|
3P |
||||||||||
|
1P |
64 |
7 |
Singleend |
2SE + 1 |
5 |
Yes |
128 (32x4) |
12 |
2 |
|
|
1P |
64 |
7 |
Singleend |
2SE + 1 |
5 |
Yes |
128 (32x4) |
12 |
2 |
|
|
3P |
64 |
7 |
Singleend |
3SE + 3 |
5 |
Yes |
168 (42x4) |
22 |
2 |
|
|
3P |
64 |
7 |
Singleend |
3SE + 3 |
5 |
Yes |
168 (42x4) |
22 |
2 |
|
|
3P |
64 |
7 |
Singleend |
3SE + 3 |
5 |
Yes |
8 |
1 |
||
|
1P/2P |
128 |
4 |
Singleend |
2SE + 2 |
10 |
Yes |
156 (39x4) |
22 |
2 |
|
|
1P/2P |
256 |
4 |
Singleend |
2SE + 2 |
10 |
Yes |
156 (39x4) |
22 |
2 |
|
|
1P/2P |
128 |
4 |
Differential |
2D + 2 |
10 |
Yes |
268 (67x4) |
43 |
2 |
|
|
1P/2P |
256 |
4 |
Differential |
2D + 2 |
10 |
Yes |
268 (67x4) |
43 |
2 |
|
|
3P |
128 |
4 |
Differential |
4D + 3 |
10 |
Yes |
228 (57x4) |
39 |
2 |
|
|
3P |
128 |
4 |
Differential |
4D + 3 |
10 |
Yes |
228 (57x4) |
39 |
2 |
|
|
3P |
128 |
4 |
Differential |
4D + 3 |
10 |
Yes |
300 (75x4) |
52 |
2 |
|
|
3P |
256 |
4 |
Differential |
4D + 3 |
10 |
Yes |
300 (75x4) |
52 |
2 |
|
|
1P |
32 |
3 |
Differential |
2D + 1 |
5 |
Yes |
222 (37x6) |
30 |
2 |
|
|
1P |
64 |
5 |
Differential |
2D + 1 |
5 |
Yes |
222 (37x6) |
30 |
2 |
|
|
1P |
128 |
5 |
Differential |
2D + 1 |
5 |
Yes |
222 (37x6) |
30 |
2 |
|
|
1P/2P |
64 |
5 |
Differential |
2D + 2 |
5 |
Yes |
336 (56x6) |
51 |
2 |
|
|
1P/2P |
128 |
5 |
Differential |
2D + 2 |
5 |
Yes |
336 (56x6) |
51 |
2 |
|
|
3P |
64 |
5 |
Differential |
4D + 3 |
5 |
Yes |
336 (56x6) |
51 |
2 |
|
|
3P |
128 |
5 |
Differential |
4D + 3 |
5 |
Yes |
336 (56x6) |
51 |
2 |
|
|
3P |
128 |
5 |
Differential |
4D + 3 |
5 |
Yes |
336 (56x6) |
51 |
2 |
|
|
3P |
64 |
5 |
Differential |
4D + 3 |
5 |
Yes |
336 (56x6) |
51 |
2 |
|
|
3P |
64 |
5 |
Differential |
4D + 3 |
5 |
Yes |
29 |
1 |
||
|
3P |
64 |
5 |
Differential |
4D + 3 |
5 |
Yes |
29 |
1 |
||
|
1P |
||||||||||
|
1P ,3P |
0 |
0 |
Differential |
2D |
300(50x6) |
70 |
0 |
|||
|
1P/2P |
64 |
8 |
Differential |
2D + 2 |
10 |
Yes |
156(39x4) 190(38X5) 222(37x6) |
39 |
3 |
|
|
1P/2P |
128 |
8 |
Differential |
2D + 2 |
10 |
Yes |
156(39x4) 190(38X5) 222(37x6) |
39 |
3 |
|
|
1P |
256 |
|||||||||
