Product information query
Products News
首页 > Products > Battery Charging Chip > Plumbic Phosphoric Battery Charging IC > Phosphoric Battery Charging IC >The cxlb7210 is a PWM mode lithium battery or lithium iron phosphate battery charging management integrated circuit, which can independently manage the charging of single
The cxlb7210 is a PWM mode lithium battery or lithium iron phosphate battery charging management integrated circuit, which can independently manage the charging of single

The cxlb7210 is a PWM mode lithium battery or lithium iron phosphate battery charging management integrated circuit, which can independently manage the charging of single or multiple lithium batteries or lithium iron phosphate batteries. It has the advantages of small package, less peripheral components and simple use. Cxlb7210 has constant current and voltage charging mode, which is very suitable for lithium battery or lithium iron phosphate battery. Cxlb7210 has constant current and voltage charging mode, which is very suitable for lithium battery or lithium iron phosphate battery or lithium iron phosphate battery. In the constant voltage charging mode, the constant voltage charging voltage is set by the external resistance partial voltage network; in the constant current charging mode, the charging current is set by an external resistance. For deeply discharged batteries, when the battery voltage is lower than 66.7% of the set constant voltage charging voltage, the cxlb7210 uses 15% of the set constant current charging current to charge the battery
Trickle charging. In the constant voltage charging stage, the charging current decreases gradually. When the charging current decreases to the value set by the external resistance, the charging ends. At the end of charging state, if the battery voltage drops to 91.1% of the set constant voltage charging voltage, a new charging cycle will start automatically

The cxlb7210 is a PWM mode lithium battery or lithium iron phosphate battery charging management integrated circuit, which can independently manage the charging of single
Manual
Ordering

Ordering

Product introduction

5A 多类型电池充电管理集成电路CXLB7210   
产品简介  技术规格书下载  产品演试板使用说明
概述:
​CXLB7210是PWM降压模式锂电池或磷酸铁锂电池充电管理集成电路,独立对单节或多节锂电池或磷酸铁锂电池充电进行自动管
理,具有封装外形小,外围器件少和使用简单等优点
CXLB7210具有恒流和恒压充电模式,非常适合锂电池或磷酸铁锂电池CXLB7210具有恒流和恒压充电模式,非常适合锂电池或磷
酸铁锂电池或磷酸铁锂电池的充电。在恒压充电模式,恒压充电电压由外部电阻分压网络设置;在恒流充电模式,充电电
流通过一个外部电阻设置。
对于深度放电的电池,当电池电压低于所设置的恒压充电电压的66.7%时,CXLB7210用所设置的恒流充电电流的15%对电池进
行涓流充电。在恒压充电阶段,充电电流逐渐减小,当充电电流降低到外部电阻所设置的值时,充电结束。在充电结束状
态,如果电池电压下降到所设置的恒压充电电压的91.1%时,自动开始新的充电周期。当输入电源掉电或者输入电压低于电
池电压时,CXLB7210自动进入低功耗的睡眠模式。
其它功能包括输入低电压锁存,电池温度监测,电池端过压保护和充电状态指示等。
CXLB7210采用16管脚TSSOP封装。
 
应用
磷酸铁锂电池充电 笔记本电脑
备用电池应用 便携式工业和医疗仪器
电动工具 独立电池充电器
 
特点:
宽输入电压范围:7.5V 到28V
对单节或多节锂电池或磷酸铁锂电池进行完整的充电管理
恒压充电电压由外部电阻分压网络设置
充电电流达5A
PWM开关频率:300KHz
恒流充电电流由外部电阻设置
对深度放电的电池进行涓流充电
充电结束电流可由外部电阻设置
电池温度监测功能
自动再充电功能
充电状态和充电结束状态指示
软启动功能
电池端过压保护
工作环境温度:-40℃到+85℃
采用16管脚TSSOP 封装
产品无铅,无卤素元素,满足RoHS
 
产品封装图:nEY嘉泰姆
blob.png 
电路原图:nEY嘉泰姆
blob.png 
  • 相关电子充电芯片nEY嘉泰姆

  •  nEY嘉泰姆

型号 电池种类/串联数量 工作模式 最高输入电压 最大持续充电电流 充电结束判断 封装
CXLB7206 锂电池/1 开关模式 28V 4A 最小充电电流 SSOP10
CXLB7207 锂电池/1 开关模式 28V 4A 最小充电电流 SSOP10
CXLB7208 锂电池/1 开关模式 28V 4A 最小充电电流 SSOP10
CXLB7209 锂电池、磷酸铁锂电池/多节 开关模式 +28V 5A 最小充电电流 可外部设置 TSSOP16
CXLB7210 锂电池、磷酸铁锂电池/多节 开关模式 +28V 5A 最小充电电流 可外部设置 TSSOP16
CXLB7211 锂电池/1 线性模式 +6V 1A 最小充电电流 SOP8
CXLB7212 锂电池/1 线性模式 +6.5V SOP8/PP 1A;SOP8 500mA 最小充电电流 SOP8/PP,SOP8
CXLB7213 锂电池/1 线性模式 +6.5V 1A 最小充电电流 SOP8
CXLB7214B 锂电池/1 线性模式 +6V 1A 最小充电电流 DFN8
CXLB7215 锂电池/1 线性模式 +6V 1A 最小充电电流 DFN8
CXLB7216 锂电池/1 线性模式 +6V 600mA 最小充电电流 SOP8
CXLB7217 锂电池/1 线性模式 +6V 600mA 最小充电电流 SOP8
CXLB7218A 锂电池/1 线性模式 +6V 600mA 最小充电电流 SOP8